Publicaciones (20) Publicaciones en las que ha participado algún/a investigador/a

2004

  1. A large haptic device for aircraft engine maintainability

    IEEE Computer Graphics and Applications, Vol. 24, Núm. 6, pp. 70-74

  2. Aplicación de las técnicas de EBSD al estudio de la transformación [gamma-alfa] en aceros microaleados

    Revista de metalurgia, Vol. 40, Núm. 5, pp. 359-364

  3. Approximation of optimal voxel size for collision detection in maintainability simulations within massive virtual environments

    Computer Graphics Forum, Vol. 23, Núm. 1, pp. 13-23

  4. Effects of powder processing on densification of titanium diboride based cermets

    Powder Metallurgy, Vol. 47, Núm. 1, pp. 65-72

  5. Experimental Quantitative Comparison of Different Control Architectures for Master-Slave Teleoperation

    IEEE Transactions on Control Systems Technology, Vol. 12, Núm. 1, pp. 2-11

  6. Femtosecond studies of electron capture times in InGaN/GaN multiple quantum wells

    Applied Physics Letters, Vol. 84, Núm. 16, pp. 3052-3054

  7. GMR effect in CuCo annealed melt-spun ribbons

    Journal of Nanoscience and Nanotechnology, Vol. 4, Núm. 8, pp. 1056-1061

  8. High Temperature Circular Position Sensor Based on a Giant Magnetoresistance Nanogranular AgxCo1-x Alloy

    IEEE Sensors Journal, Vol. 4, Núm. 2, pp. 221-225

  9. Influence of thermo-mechanical processing on the microstructure of Cu-based shape memory alloys produced by powder metallurgy

    Materials Science and Engineering A, Vol. 378, Núm. 1-2 SPEC. ISS., pp. 263-268

  10. Liquid phase sintering of SiC with additions of Y2O3, Al2O3 and SiO2

    Journal of the European Ceramic Society, Vol. 24, Núm. 9, pp. 2895-2903

  11. Measuring the strain rate sensitivity by instrumented indentation Application to an ultrafine grain (equal channel angular-pressed) eutectic Sn-Bi alloy

    Journal of Materials Research, Vol. 19, Núm. 1, pp. 282-290

  12. Microstructural characterisation of an alumina/mullite composite tested in creep

    Materials Science and Engineering A, Vol. 368, Núm. 1-2, pp. 139-144

  13. Modeling of austenite grain size distribution in Nb microalloyed steels processed by thin slab casting and direct rolling (TSDR) route

    ISIJ International, Vol. 44, Núm. 8, pp. 1416-1425

  14. Obtención de microestructuras de grano ultrafino en aleaciones de aluminio mediante extrusión en canal angular (ECAE)

    Boletín de la Sociedad Española de Cerámica y Vidrio, Vol. 43, Núm. 2, pp. 172-174

  15. Recovery during annealing in a cold rolled low carbon steel. Part I: Kinetics and microstructural characterization

    Acta Materialia, Vol. 52, Núm. 12, pp. 3657-3664

  16. Recovery during annealing in a cold rolled low carbon steel. Part II: Modelling the kinetics

    Acta Materialia, Vol. 52, Núm. 12, pp. 3665-3670

  17. Simulation of liquid phase sintering using the Monte Carlo method

    Materials Science and Engineering A, Vol. 365, Núm. 1-2, pp. 151-155

  18. Stability analysis of a 1 DOF haptic interface using the Routh-Hurwitz criterion

    IEEE Transactions on Control Systems Technology, Vol. 12, Núm. 4, pp. 583-588

  19. Study of the Ferrite Grain Coarsening behind the Transformation Front by Electron Backscattered Diffraction Techniques

    Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, Vol. 35 A, Núm. 1, pp. 93-102

  20. Study of the strain reversal effect on the recrystallization and strain-induced precipitation in a Nb-microalloyed steel

    Acta Materialia, Vol. 52, Núm. 2, pp. 333-341