Asociación Centro Tecnológico Ceit (CEIT)

2008

1. An FFT core for DVB-T/DVB-H receivers

   VLSI Design, Vol. 2008

2. Analysis of coherence strategies for stereo occlusion culling

   Computer Animation and Virtual Worlds, Vol. 19, Núm. 1, pp. 67-77

3. AqquaScan: Design and implementation of an internet-based service for the remote monitoring and management of decentralised WWTPs

   Water Science and Technology, Vol. 57, Núm. 10, pp. 1495-1502

4. Characterization and modelling of the residual stresses induced by belt finishing on a AISI52100 hardened steel

   Journal of Materials Processing Technology, Vol. 208, Núm. 1-3, pp. 187-195

5. Critical examination of strain-rate sensitivity measurement by nanoindentation methods: Application to severely deformed niobium

   Acta Materialia, Vol. 56, Núm. 4, pp. 884-893

6. Development of powder metallurgy T42 high speed steel for structural applications

   Journal of Materials Processing Technology, Vol. 202, Núm. 1-3, pp. 521-527

7. Effect of stored energy and recovery on the overall recrystallization kinetics of a cold rolled low carbon steel

   Materials Science and Engineering A, Vol. 485, Núm. 1-2, pp. 200-209

8. Efficacy of magnetic inductive parameters for annealing characterization of cold rolled low carbon steel

   IEEE Transactions on Magnetics, Vol. 44, Núm. 11 PART 2, pp. 3839-3842

9. Electro-discharge machining (EDM) versus hard turning and grinding-Comparison of residual stresses and surface integrity generated in AISI O1 tool steel

   Journal of Materials Processing Technology, Vol. 195, Núm. 1-3, pp. 186-194

10. Formation of fine grained globular microstructures during isothermal annealing of PM T42 high speed steel: Role of nanometric proeutectoid carbides

    Materials Science and Technology, Vol. 24, Núm. 1, pp. 26-32

11. Full-body performance animation with Sequential Inverse Kinematics

    Graphical Models, Vol. 70, Núm. 5, pp. 87-104

12. GPU local triangulation: An interpolating surface reconstruction algorithm

    Computer Graphics Forum, Vol. 27, Núm. 3, pp. 807-814

13. Hard turning plus grinding-a combination to obtain good surface integrity in AISI O1 tool steel machined parts

    Machining Science and Technology, Vol. 12, Núm. 1, pp. 15-32

14. High-performance linear cable transmission

    Journal of Mechanical Design, Transactions of the ASME, Vol. 130, Núm. 6, pp. 0645011-0645015

15. Improved model of kinetics of strain induced precipitation and microstructure evolution of Nb microalloyed steels during multipass rolling

    ISIJ International, Vol. 48, Núm. 10, pp. 1457-1466

16. In situ neutron diffraction study of internal micro-stresses developed by plastic elongation in <110> textured BCC wires

    Advanced Engineering Materials, Vol. 10, Núm. 10, pp. 951-954

17. Influence of silver as an additive on BaTiO3-CuO thin film for CO2 monitoring

    Sensors and Actuators, B: Chemical, Vol. 129, Núm. 1, pp. 386-390

18. Low frequency noise optimization in gilbert-cell-based mixers for direct 3 conversion (zero-if) receivers

    Microwave and Optical Technology Letters, Vol. 50, Núm. 12, pp. 3128-3131

19. Master sintering curve for densification derived from a constitutive equation with consideration of grain growth: Application to tungsten heavy alloys

    Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, Vol. 39, Núm. 12, pp. 2941-2948

20. Model-based optimisation of Wastewater Treatment Plants design

    Environmental Modelling and Software, Vol. 23, Núm. 4, pp. 435-450