Artículos (36) Publicaciones en las que ha participado algún/a investigador/a

2011

  1. A 16-kV HBM RF ESD protection codesign for a 1-mW CMOS direct conversion receiver operating in the 2.4-GHz ISM band

    IEEE Transactions on Microwave Theory and Techniques, Vol. 59, Núm. 9, pp. 2318-2330

  2. A comparison of the effects of multi-wall and single-wall carbon nanotube additions on the properties of zirconia toughened alumina composites

    Carbon, Vol. 49, Núm. 5, pp. 1599-1607

  3. A knowledge-based control system for air-scour optimisation in membrane bioreactors

    Water Science and Technology, Vol. 63, Núm. 9, pp. 2025-2031

  4. AAL for supporting elderly

    2011 IST-Africa Conference Proceedings, IST 2011

  5. ADD CONTROL: Advanced control solutions for waste water treatment

    Reviews in Environmental Science and Biotechnology, Vol. 10, Núm. 1, pp. 3-7

  6. An optimization method for overdetermined kinematic problems formulated with natural coordinates

    Multibody System Dynamics, Vol. 26, Núm. 4, pp. 397-410

  7. Analytical calculation of the flux distribution and demagnetization in spoke interior permanent-magnet machines with non-magnetic shaft

    International Review of Electrical Engineering, Vol. 6, Núm. 3, pp. 1228-1238

  8. Assessment of the influence of thermal pre-treatment time on the macromolecular composition and anaerobic biodegradability of sewage sludge

    Bioresource Technology, Vol. 102, Núm. 2, pp. 660-666

  9. Automatic characterisation of primary, secondary and mixed sludge inflow in terms of the mathematical generalised sludge digester model

    Water Science and Technology, Vol. 64, Núm. 3, pp. 557-567

  10. Battery response analyzer using a high current DC-DC converter as an electronic load

    Renewable Energy and Power Quality Journal, Vol. 1, Núm. 9, pp. 611-615

  11. CALHIDRA 3.0 - New software application for river water quality prediction based on RWQM1

    Environmental Modelling and Software, Vol. 26, Núm. 7, pp. 973-979

  12. Combined model to describe both the mechanical and microstructural transients under a reversal of strain

    Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science, Vol. 42, Núm. 9, pp. 2633-2642

  13. Comparative analysis of QCM and SPR techniques for the optimization of immobilization sequences

    Sensors and Actuators, B: Chemical, Vol. 155, Núm. 2, pp. 667-672

  14. Comparison of the oxidation behaviour of WC-Co and WC-Ni-Co-Cr cemented carbides

    Corrosion Science, Vol. 53, Núm. 9, pp. 2754-2760

  15. Consolidation of (Ti,Mo)(C,N)-Ni cermets by glass encapsulated hot isostatic pressing

    Materials Science and Engineering A, Vol. 528, Núm. 13-14, pp. 4453-4461

  16. Dependence of the order and crack density of polystyrene opals on volume fraction, humidity and temperature

    Crystal Research and Technology, Vol. 46, Núm. 10, pp. 1044-1050

  17. Diffusional Monte Carlo model of liquid-phase sintering

    Mathematics and Computers in Simulation, Vol. 81, Núm. 11, pp. 2564-2580

  18. Effect of austenite microstructure and cooling rate on transformation characteristics in a low carbon Nb-V microalloyed steel

    Materials Science and Engineering A, Vol. 528, Núm. 6, pp. 2559-2569

  19. GMR sensors: Magnetoresistive behaviour optimization for biological detection by means of superparamagnetic nanoparticles

    Biosensors and Bioelectronics, Vol. 26, Núm. 8, pp. 3705-3709

  20. HF Antenna design optimization for railway spot signalling systems

    Microwave and Optical Technology Letters, Vol. 53, Núm. 12, pp. 2742-2746