Publicaciones en las que colabora con Ibon Elosegui Simón (22)

2023

  1. Novel composition of Nd-Fe-B gas atomized powder to produce compression bonded magnets

    Advanced Powder Technology, Vol. 34, Núm. 11

2022

  1. Review of High Power and High Voltage Electric Motors for Single-Aisle Regional Aircraft

    IEEE Access, Vol. 10, pp. 112989-113004

2021

  1. Eliminating rare earth permanent magnets on low-speed high-torque machines: A performance and cost comparison of synchronous reluctance machines, ferrite permanent magnet-synchronous reluctance machines and permanent magnet synchronous machines for a direct-drive elevator system

    IET Electric Power Applications, Vol. 15, Núm. 3, pp. 370-378

2018

  1. Node mapping criterion for highly saturated interior PMSMs using magnetic reluctance network

    Energies, Vol. 11, Núm. 9

  2. Optimal pole number and winding designs for low speed-high torque synchronous reluctance machines

    Energies, Vol. 11, Núm. 1

  3. Wafter design for totally enclosed electric machines

    Applied Thermal Engineering, Vol. 129, pp. 93-105

2017

  1. Design criteria for water cooled systems of induction machines

    Applied Thermal Engineering, Vol. 114, pp. 1018-1028

2016

  1. A simple model for fault analysis of multiphase PMSM drives

    2016 International Conference on Electrical Systems for Aircraft, Railway, Ship Propulsion and Road Vehicles and International Transportation Electrification Conference, ESARS-ITEC 2016

  2. Analysis and comparison of algebraic approaches for highly saturated Surface PMSM

    2016 International Symposium on Power Electronics, Electrical Drives, Automation and Motion, SPEEDAM 2016

2015

  1. Analysis of relevant aspects of thermal and hydraulic modeling of electric machines. Application in an Open Self Ventilated machine

    Applied Thermal Engineering, Vol. 75, pp. 277-288

  2. Analytical Calculation of the Slot Leakage Inductance in Fractional-Slot Concentrated-Winding Machines

    IEEE Transactions on Industrial Electronics, Vol. 62, Núm. 5, pp. 2742-2752

  3. Coupled thermal and hydraulic algebraic models for an open self-ventilated induction machine

    IET Electric Power Applications, Vol. 9, Núm. 8, pp. 513-522

  4. Fault-tolerant permanent magnet synchronous machine - phase, pole and slot number selection criterion based on inductance calculation

    IET Electric Power Applications, Vol. 9, Núm. 2, pp. 138-149

  5. Manufacturing of isotropic bonded NdFeB Magnets from Gas atomised powders

    Proceedings Euro PM 2015: International Power Metallurgy Congress and Exhibition

2014

  1. Analytical sizing methodology for inductive power transfer systems

    2014 IEEE 15th Workshop on Control and Modeling for Power Electronics, COMPEL 2014

2013

  1. Coupled electromagnetic and thermal design of miniaturized permanent magnet linear motors for sliding door applications

    International Review of Electrical Engineering, Vol. 8, Núm. 5, pp. 1416-1426

2011

  1. Analytical calculation of the flux distribution and demagnetization in spoke interior permanent-magnet machines with non-magnetic shaft

    International Review of Electrical Engineering, Vol. 6, Núm. 3, pp. 1228-1238

2008

  1. Fast sizing and simulation of multipole radial flux permanent magnet synchronous machines

    SPEEDAM 2008 - International Symposium on Power Electronics, Electrical Drives, Automation and Motion

  2. Flat magnets in surface-mounted permanent magnet machines

    Conference Record - IAS Annual Meeting (IEEE Industry Applications Society)

  3. Flat magnets in surface-mounted permanent magnet machines: Influence and design

    SPEEDAM 2008 - International Symposium on Power Electronics, Electrical Drives, Automation and Motion